專業、敬業、樂業
一、產品信息 Product Information
產品名稱 Name: Lithium Iron Phosphate
化 學 式 Formula: LiFePO4
分 子 量 Molecular weight: 157.76 g/mol
產品特點 放電比容量高;倍率性能優異;穩定性佳;低溫性能好;循環壽命長;安全性能好。
Features: High specific discharge capacity; Good ratio performance; Excellent stability; Good low temp. performance; Long cycle life; Perfect safety.
二、產品型號 Product Model
本說明書對應的產品的型號為ANZLFP—G,屬于常規型號。
The model of the product mentioned in the specification is ANZLFP—G, belonging to the conventional models.
三、主要物理指標 Main Physical Parameters
四、主要電化學性能 Main Electrochemical Parameters
五、限用物質含量 Restricted Substances
六、應用要點 Application Key Points
1.材料配方(油系):磷酸鐵鋰(LFP) 導電炭黑(SP) 導電石墨(KS-6) PVDF(PVDF)
Non-aqueous prescription (91-92)% (2.5-3)% (1-1.5)% (4.5-5.5)%
2.材料配方(水系):磷酸鐵鋰(LFP) 導電炭黑(SP) 導電石墨(KS-6) 水性粘結劑(LA133)
Aqueous prescription (90-92)% (2.5-3)% (1.5-2)% (3.0-4.0)%
3.涂覆的面密度可以控制在150—190g/m2,水系材料的面密度還可以適當的上調。
The coated surface density can be controlled between 150—190g/m2 ,aqueous material can be raised appropriately.
4.油系配方的粘度控制在5000MPa.s左右比較合適、水系控制在4000MPa.s左右比較合適。
The viscosity of non-aqueous prescription can be controlled around 5000MPa.s, while aqueous prescription are around 4000MPa.s.
5.涂布中,油系配方的烘烤溫度控制在120度以下,水系配方的烘烤溫度在100度左右比較合適。
In the coating process, non-aqueous prescription baking temperature should be controlled below 120℃,aqueous prescription about 100℃.
6.材料的壓實密度可以達到2.6以上,建議設計壓實密度在2.6左右。
The compacted density of material can reach more than 2.6, recommended designed compacted density around 2.6.
七、注意事項 Cautions
個人防護 Personal precautions
避免吸入蒸汽、霧或氣體以及粉塵的形成。
Avoid breathing in vaporous, mist or gas and dust formation.
儲存方式 Storage
儲存在涼爽的地方,保持容器密閉在干燥、通風良好處。
Store in cool place. Keep container tightly closed in a dry and well-ventilated place.
廢物處理 Waste treatment methods
把剩余和不能循環利用的提供給經授權的處理廠家。
Offer surplus and non-recyclable products to a licensed disposal company.
產品質保 Warranty 12個月 (12 months)
八、其他事項 Others
1.由于測試方法、檢測儀器使用等的不同,本規格書中部分指標可能與客戶要求不能完全一致,可以在協商溝通后可以在協商溝通后進行統一。
Due to the different test methods and test equipments, parts of the indicators in this specification may not completely consistent with the customer’s requirements, it can be unified after negotiation.
2.特殊要求或特殊規格產品,若技術指標不在本說明規定范圍內,經與客戶共同協商、評估后重新確定規格要求
Specially required product, if the technical indicator is beyond the scope of this specification, it can be determined after negotiation and evaluation with customer.
3.本公司產品水分含量已經過嚴格控制,凡購買本公司產品后,客戶勿須再進行烘烤可直接投料。
The moisture content of our product has been strictly controlled, for every purchase of our product, it can be used directly,and no need to roast again.